Add to cart successfully!
7 days free paymentrefund after 7-14 days
100% genuine product
1. Characteristics of the 30kVA LiOA BC3630 power converter transformer
The DC output voltage changes as desired from 0V to 18V.
Automatically compare the charging current of the battery.
Automatically reduce the charging current when the battery is fully charged.
The meter clearly displays DC voltage (V) and current (A) so it is easy to observe and use. .
In cases where the battery is damaged, out of power... and needs to be forced to charge, charging a LiOA battery is a great solution.
Power converter transformer 30kVA LiOA BC3630 b Overcurrent and short circuit protection... by Aptomat makes restarting easy (unlike other battery chargers that use fuses, so when the fuse is blown, it is very difficult to replace)
LiOA BC3630 30kVA power converter transformer
2. User manual
< When you first buy it, you must fully charge the battery. Usually the first charge time is about 12-14 hours. After fully charging, you discharge the battery until it runs out of power and then recharge it again before using it.When the battery discharges , if the voltage drops to 1.80V/cell (equivalent to U = 10.80V for 12V battery), you must stop discharging and recharge immediately to avoid the battery being starved for too long. Fully charge the battery before using it. out for reuse. Normally, with the battery load, the charging time usually lasts from 8 to 12 hours.
- “No electricity”: When the voltage at two The measured battery voltage is 6.2 – 6.5V for a 6V battery, 8.3 – 8.5V for an 8V battery, 12.4 – 12.54V for a 12V battery.
- Charging current: Rated charging voltage is usually 1.2 – 1.25 times the battery voltage. Continuous charging with voltage stabilization mode U = 2.40V – 2.50V (with 2V battery), U =14.4 – 14.5V (with 12V battery). The charging current must not exceed 0.1 - 0.2 times the rated capacity of the battery (for example: with a 100AH battery, the maximum charging current is < 10A - 20A)
- Electrolyte temperature: Must not exceed 50 degrees Celsius. If the temperature exceeds this value, charging must be stopped to lower the temperature by reducing the charging current until the temperature stabilizes. Thus , the charging time must be increased accordingly to ensure charging capacity.
1. Characteristics of the 30kVA LiOA BC3630 power converter transformer
The DC output voltage changes as desired from 0V to 18V.
Automatically compare the charging current of the battery.
Automatically reduce the charging current when the battery is fully charged.
The meter clearly displays DC voltage (V) and current (A) so it is easy to observe and use. .
In cases where the battery is damaged, out of power... and needs to be forced to charge, charging a LiOA battery is a great solution.
Power converter transformer 30kVA LiOA BC3630 b Overcurrent and short circuit protection... by Aptomat makes restarting easy (unlike other battery chargers that use fuses, so when the fuse is blown, it is very difficult to replace)
LiOA BC3630 30kVA power converter transformer
2. User manual
< When you first buy it, you must fully charge the battery. Usually the first charge time is about 12-14 hours. After fully charging, you discharge the battery until it runs out of power and then recharge it again before using it.When the battery discharges , if the voltage drops to 1.80V/cell (equivalent to U = 10.80V for 12V battery), you must stop discharging and recharge immediately to avoid the battery being starved for too long. Fully charge the battery before using it. out for reuse. Normally, with the battery load, the charging time usually lasts from 8 to 12 hours.
- “No electricity”: When the voltage at two The measured battery voltage is 6.2 – 6.5V for a 6V battery, 8.3 – 8.5V for an 8V battery, 12.4 – 12.54V for a 12V battery.
- Charging current: Rated charging voltage is usually 1.2 – 1.25 times the battery voltage. Continuous charging with voltage stabilization mode U = 2.40V – 2.50V (with 2V battery), U =14.4 – 14.5V (with 12V battery). The charging current must not exceed 0.1 - 0.2 times the rated capacity of the battery (for example: with a 100AH battery, the maximum charging current is < 10A - 20A)
- Electrolyte temperature: Must not exceed 50 degrees Celsius. If the temperature exceeds this value, charging must be stopped to lower the temperature by reducing the charging current until the temperature stabilizes. Thus , the charging time must be increased accordingly to ensure charging capacity.
30kVA LiOA BC3630 power converter transformer
1. Characteristics of the 30kVA LiOA BC3630 power converter transformer
The DC output voltage changes as desired from 0V to 18V.
Automatically compare the charging current of the battery.
Automatically reduce the charging current when the battery is fully charged.
The meter clearly displays DC voltage (V) and current (A) so it is easy to observe and use. .
In cases where the battery is damaged, out of power... and needs to be forced to charge, charging a LiOA battery is a great solution.
Power converter transformer 30kVA LiOA BC3630 b Overcurrent and short circuit protection... by Aptomat makes restarting easy (unlike other battery chargers that use fuses, so when the fuse is blown, it is very difficult to replace)
LiOA BC3630 30kVA power converter transformer
2. User manual
< When you first buy it, you must fully charge the battery. Usually the first charge time is about 12-14 hours. After fully charging, you discharge the battery until it runs out of power and then recharge it again before using it.When the battery discharges , if the voltage drops to 1.80V/cell (equivalent to U = 10.80V for 12V battery), you must stop discharging and recharge immediately to avoid the battery being starved for too long. Fully charge the battery before using it. out for reuse. Normally, with the battery load, the charging time usually lasts from 8 to 12 hours.
- “No electricity”: When the voltage at two The measured battery voltage is 6.2 – 6.5V for a 6V battery, 8.3 – 8.5V for an 8V battery, 12.4 – 12.54V for a 12V battery.
- Charging current: Rated charging voltage is usually 1.2 – 1.25 times the battery voltage. Continuous charging with voltage stabilization mode U = 2.40V – 2.50V (with 2V battery), U =14.4 – 14.5V (with 12V battery). The charging current must not exceed 0.1 - 0.2 times the rated capacity of the battery (for example: with a 100AH battery, the maximum charging current is < 10A - 20A)
- Electrolyte temperature: Must not exceed 50 degrees Celsius. If the temperature exceeds this value, charging must be stopped to lower the temperature by reducing the charging current until the temperature stabilizes. Thus , the charging time must be increased accordingly to ensure charging capacity.
7 days free paymentrefund after 7-14 days
100% genuine product
Buy now
